Sarwinplast Wallputty
Packaging: 40 Kg Bag
Sarwinplast-Wallputty is a white cement based polymer modified wall putty specially developed as a base coat to cover unevenness and pinholes on plastered, mortar wall (Internal) and ceiling to make the surface wall white and smooth and ready for primer and paint application.
Water
Resistant
Smooth
Finishing
Long
Lasting
Superior
Paint Finish
METHOD OF USAGE
SURFACE PREPARATION:
- Clean loose particles, dirt, grease and traces of adhering material from the wall surface with the help of sand paper, putty blade or by wire brush.
- For loose plastered areas, remove the defective material and re-plaster the area with Sarwinplast Ready-Mix Plaster.
- For ceiling/wall, which are not even, re-plaster it with Sarwinplast Ready-Mix Plaster to make them even.
- If any cracks in base plaster, fill it by using Sarwinplast Crack Filler. Moisten the surface with sufficient quantity of clean water.
MIXING:
- Take 300-450 ml of clean water for 1 Kg of Sarwinplast Wall Putty in a clean bucket
- It is very important that Sarwinplast Wall Putty to be added in water and not vice versa
- Stir continuously by using an electric mixer or by hand to obtain a homogeneous Lump-free paste
- Allow the resultant paste to stand for about 10 minutes for additives to dissolve completely.
- Re-mix again for about 2 minutes. The paste is now ready for application.
- Use the mix within 30 minutes.
APPLICATION:
- Apply 1st coat with the help of a steel trowel or putty blade to a thickness of about 0.5-1 mm and let it dry for at least 3 hours.
- Level and smoothen the surface. Cure the first coat lightly after it dries
- Apply the 2nd coat of putty to a thickness of 0.5-1 mm and leave the surface to dry completely
- The thickness of each coat should not exceed more than 1 mm and total putty thickness Less than 2 mm.
- If required to remove any unevenness before any paint application, Level the surface with very fine emery paper not less than 600 no
- For better result, it is always recommend to let the surface to dry overnight for at Least 10-12 hours
CAUTION:
- Do not use hook
- Store in a cool dry place
- Increase of contact with eyes for open wound rings out quickly with fresh water
HEALTH & SAFETY INFORMATION:
contact may irritate eyes of sensitive skin, dust may irritate respiratory systems. Prevent eye contact , Rinse with water, Ask for medical advice, Avoid extended contact with skin, Clean with water, Avoid breathing dust, aerate area, Move to fresh air, Avoid ingestion, Wash mouth, Drink water, Wear appropriate clothing, gloves, eye protection and dust mask
Key Features
- True colour tone of the paint is maintained, Primer is not required
- Protects expensive paint from dampness, peeling off and flaking
- Excellent workability
- Paint finish is superio
- Whitest putty
- Highly water resistant
- Strong bonding to the base plaster
- Smooth finish
- Durable & long lasting
- Reduces paint consumption Avoid
- frequent repainting Cost-effective
- Aesthetic look for ceiling, interior and external wal
- Ease of use at site
Note:
Generally the cause of efflorescence on the wall surface is due to brick masonry and the quality of bricks, sand and water. If the effect of efflorescence is very high on the brick masonry then proper care should be taken to control the efflorescence. The efflorescence on brick masonry if allowed to exist which will impair the bonding of the -Sarwinplast Wallputty- as is with any other products
Precautions:
Sarwinplast Wallputty contains only eco-friendly fillers and additives. However, being white cement based, it is alkaline and hence it is advisable to avoid direct eye and skin contact with this. In case of eye contact, flush with clean water for at least 15 minutes and seek for medical help. Recommended to keep it out of children reach.
