HD-MR Gypsum Plaster
Packaging: 25 Kg Bag
Sarwinplast-HD-MR : Super White High Density Moisture Resistant Gypsum Plaster : Sarwin Gypsum Plaster is a High-density light weight Polymerised gypsum plaster suitable for application on most internal surfaces including brick, block and concrete. It consists of superior quality high density gypsum, formulated with special additives to enhance working and setting characteristics, also improves workability and coverage. When dry, it provides superior whiteness, hard, smooth finish and is suitable for all internal dry plastering applications.
Humidity
Resistant
Light
Weight
Super
Coverage
Pure
Gypsum
METHOD OF USAGE
PREPARATION:
- Clean loose particles, dirt, grease and traces of adhering material from the wall surface with the help of sand paper, putty blade or by wire brush.
- Pre-wet the surface before application to achieve good workability and higher coverage.
PREPARATION & APPLICATION:
- Mix Sarwin Gypsum Plaster to water and not water to powder
- Water to plaster ratio should be (1 part of water and 1.5 part of gypsum plaster) to be maintained to provide a good cohesive workable mix
- Mix Sarwin Gypsum Plaster to water with the help of hand to form a uniform lump free paste.
- Install the wooden or steel strip/dhada or install the leveling strip in the area where the paste needs to be applied
- Apply the single coat approx. up to 8 mm to 10 mm of thickness, before the first coat sets rake and cross rake the surface
- Fill in any hollow area, Level off and compact the surface, then apply the final finish coat
- After complete drying for usually 72 hrs. (Depending on the thickness and humidity), the plain smooth leveled surface is ready for painting application.
TIPS:
- Once the mix has begun to set, additional dry material should not be added, as performance properties of plaster will get altered, thus affecting workability, cohesiveness, adhesion and strength.
- A single coat should not exceed more than 8 mm to 10 mm of thickness. If at all thickness required is more than 8 mm to 10 mm, then plaster needs to be applied in multiple coats.
- Use the material instantly after mixing
- Sarwin gypsum plaster should not be applied on surface which is subjected continuous seepage or dampness
CAUTION:
- Do not use hook
- Store in a cool dry place
- Increase of contact with eyes for open wound rings out quickly with fresh water
Key Features
- Superior whiteness
- Affordable
- No shrinkage cracks
- Excellent bonding
- Light in weight
- Imparts high coverage
- Zero maintenance
Benefits
- Faster setting than the conventional sand cement plaster
- Reduce structural load on building as it is 50% lighter than sand cement plaste
- Direct application on Bricks, Blocks, RCC & sand cement surface
- No water curing required Compatible with all types of paints & decorative range
- Low consumption of paint
Convert normal Gypsum to Upgrade HD Grade:
For 10 kgs of normal gypsum, use 7-7.5
ltr of pure water by sprinkling 100 g of
Sarwin polymer. Mix in to that and mix it
well, let it be to set for 3 minutes then
add 10 kgs Gypsum Powder and Mix
thoroughly to a homogeneous creamy
slurry. To achieve strong and hard
products less water may use for mixing.
Container and tools should be clean
and free from previously used set
material
Precautions:
However, being grey cement based, it
is alkaline and contains no toxic
materials in the product. Care should
be taken to avoid dust inhalation
while mixing and handling. In case of
contact with eyes, wash gently with
plenty of water, take medical advice
if needed and recommended to keep
it out of children reach.
Health & safety information:
contact may irritate eyes of sensitive skin, dust may irritate respiratory systems. Prevent eye contact , Rinse with water, Ask for medical advice, Avoid extended contact with skin, Clean with water, Avoid breathing dust, aerate area, Move to fresh air, Avoid ingestion, Wash mouth, Drink water, Wear appropriate clothing, gloves, eye protection and dust mask.
